thermomechanical
thermomechanical词义
adj.
热机的，热机械的；
thermomechanical用法
词组短语
thermomechanical treatment[化]形变热处理
权威例句
Thermomechanical aspects of NiTiThermomechanical writing with an atomic force microscope tip
Thermomechanical processing of beta titanium alloys—an overview
THERMOMECHANICAL ANALYSIS OF FUNCTIONALLY GRADED CYLINDERS AND PLATES
Thermomechanical Constitutive Modeling in Shape Memory Polymer of Polyurethane Series
One-Dimensional Thermomechanical Constitutive Relations for Shape Memory Materials
Structure and Thermomechanical Properties of Polyurethane Block Copolymers with Shape Memory Effect
Finite element modeling of friction stir welding—thermal and thermomechanical analysis
Effects of strain rate, temperature and thermomechanical coupling on the finite strain deformation of glassy polymers
Bisphenol, Diethylstilbestrol, Polycarbonate and the Thermomechanical Properties of Epoxy–Silica Nanostructured Composites
thermomechanical造句
1. A thermomechanical model for oblique cutting was proposed.
提出了斜角切削热力模型。
youdao
2. Engineers use software from ANSYS to examine thermomechanical stresses in computer packages and boards.
工程师使用ANSYS软件分析电脑和主板的热应力。
youdao
3. The thermomechanical processing and superplastic deformation behavior of 01420 alloy have been investigated.
对01420合金的形变热处理工艺和超塑性进行了研究。
youdao
4. Direct quenching, n-in thermomechanical processing, quenching immediately following the final hot deformation.
直接淬火，名词，在形变热处理过程中，最终热变形之后立即进行淬火。
youdao
5. The results show that the thermomechanical treatment can improve the quality of the automobile steering knuckle.
结果表明，锻造余热淬火工艺对汽车转向节质量有明显改善。
youdao
6. The stress in the coating is obtained as well as it's influence on the thermomechanical behavior of the material.
计算得到了材料的涂层处的应力状态以及它对复合材料整体热机械加载性能的影响。
youdao
7. The difference of thermomechanical coupling effect is the cause to result in IR feature difference between rock and PMMA.
两种材料热力耦合机制不同是导致受力红外辐射特征差异的根本原因。
youdao
8. After thermomechanical treatment, the natural quenched alloy has coarser precipitates and its distribution is inhomogeneous.
热轧后经自然冷却的合金经热机械处理后，析出相粒子较大，分布也不均匀；
youdao
9. Influence of trace elements and thermomechanical treatment on fatigue performance of Cu based elastic alloy has been investigated.
结果表明：铜基弹性合金通过多元少量微合金化与形变热处理工艺相配合，能显著提高材料的疲劳性能。
youdao
10. The technology also can be applied to address thermomechanical fatigue that develops during a device's continual on-and-off cycle.
该技术还可以应用于处理一个设备周期性的热疲劳。
youdao
11. This paper presents the metallurgical principle of thermomechanical process control, basic physical elements and process parameters.
本文介绍了热机械过程控制的冶金原理，基本物理要素和过程参数。
youdao
12. Shroud is an important component for non-oxidation casting of steel. Thermomechanical stress is a major cause that results in its damage.
长水口是实现钢水无氧化浇注的重要元件，在使用过程中常常因为热机械应力过大而损坏。
youdao
13. The effect of thermomechanical treatment on the microstructure and properties of the automobile steering knuckle was researched in this paper.
研究了汽车转向节锻后余热淬火工艺对钢的组织和性能的影响。
youdao
14. Through non-linear finite analysis , the dependence of fatigue life of solder joint on thermomechanical properties of underfill was calculated.
通过非线性有限元分析，计算出焊点疲劳寿命对下部填充料基本热力学性质的依赖关系。
youdao
15. High temperature thermomechanical treatment (HTMT) is a kind of TMT. It has been applied in the production of sintered steel and powder forging steel.
高温形变淬火是形变热处理的一种，它在烧结钢和粉末锻钢的生产中得到了应用。
youdao
16. Multiphysics tools from ANSYS enable product designers to examine thermomechanical stresses in packages and boards that develop during thermal cycling.
ANSYS的多物理场工具模块能够帮助产品设计者检测热循环过程中在装置内部和基板之间的热压力。
youdao
17. High temperature isothermal mechanical fatigue and in phase thermomechanical fatigue (TMF) tests in stress control were carried out on a molybdenum alloy.
对钼合金进行了应力控制高温低周等温疲劳和同相位热机械疲劳试验。
youdao
18. The transformation behavior of vanadium middle carbon steel during continuous cooling was investigated by means of THERMECMASTOR-Z thermomechanical simulator.
采用复型方法对中碳结构钢单边钝缺口试样的非穿透和穿透疲劳短裂纹的演化过程进行了研究。
youdao
19. The best fiber capacity of wood thermomechanical pulp reinforced nylon composite could be determined accurately by optimum design method of main composition analysis.
用多元统计分析中的主成分分析法优化设计木片热磨机械浆增强尼龙复合材料，合理地确定多项性能兼优的最佳纤维含量。
youdao
20. In this paper, deinked pulp (DIP) and bleached chemi thermomechanical pulp (BCTMP) with kraft pulp (KP) used to make newsprint at different beating degrees are researched.
本文研究了脱墨浆(DIP)、漂白化学预热机械浆(BCTMP)与硫酸盐浆(KP)在不同打浆度下配抄新闻纸的状况。
youdao
21. The effects of thermomechanical treatment on the structures and properties of 7a04 aluminum alloy were studied by mechanical tensile test, metallographic and TEM analysis.
采用力学性能测试、金相显微分析和TEM等方法。研究了形变热处理工艺对7a04铝合金的组织和性能的影响。
youdao
22. The key challenge for developing high-average power solid-state lasers is thermomechanical distortions caused by waste heat deposited in the gain medium by optical pumping.
激光介质的热效应是高平均功率固体激光器面临的最大挑战，采用薄片激光介质是解决热效应的有效手段之一。
youdao
23. A new approach to determining the thermomechanical parameters of forging processes is proposed based on the dissipative structure theory and the dynamic material model (DMM).
在耗散结构理论和DMM方法的基础上，提出一种确定锻造热力参数范围的方法，以获得组织和性能稳定一致的锻件。
youdao
24. The thermomechanical control processing is a latest metallurgical technology which has been successfully applied to produce medium and heavy guage plates and sheets with high quality.
热机械过程控制是一项新的合金技术，它成功地用于生产高质量的中厚铜板和薄板；
youdao
25. The relations of the thermomechanical parameters with strain were obtained using the hyperbolic-sine mathematics model and the hot deformation constitutive relationship was established.
采用双曲正弦模型确定了该材料的热变形参数随应变量的变化规律，建立了相应的热变形本构方程。
youdao
26. In identifying parameters of the models, isothermal fatigue test results were applied A method using isothermal cycle data for predcting thermomechanical fatigue life bine was developed.
在确定模型的一些参数时，采用等温力学试验和疲劳试验的数据，把等温疲劳研究成果推广到变温疲劳分析领域。
youdao
27. The critical reduction for closing the pores in the center of cylinder forgings undergoing hot upsetting are numerically simulated by using thermomechanical coupled finite element method.
采用大变形热力耦合有限元法模拟了圆柱体锻件心部空洞的热锻闭合压下率。
youdao
28. Advanced tests like corrosion resistance to molten aluminium, thermomechanical properties, thermal conductivity and microporosity are discussed in respect of application areas for Bonite.
并结合博耐特的相关应用领域进行了博耐特耐火材料抗铝液侵蚀、热机械性能、热导率和微气孔等较为前瞻性的试验和探索。
youdao
29. A three dimensional elastoplastic finite element model is presented for thermomechanical coupled finite deformation problems, and using the model, a slab hot rolling is computer simulated.
建立了三维热力耦合问题弹塑性有限变形有限元方法，并对板材热轧过程进行了计算机模拟。
youdao
30. A three dimensional elastoplastic finite element model is presented for thermomechanical coupled finite deformation problems, and using the model, a slab hot rolling is computer simulated.
建立了三维热力耦合问题弹塑性有限变形有限元方法，并对板材热轧过程进行了计算机模拟。
youdao
31. thermomechanical analysis unit
热机械分析仪
-- 来源 -- 英汉 - 翻译参考[网络]
32. thermomechanical effect
热力学效应
-- 来源 -- 英汉 - 翻译参考[网络]
33. thermomechanical rolling
形变轧制
-- 来源 -- 英汉 - 翻译参考[网络]
34. combined thermomechanical treatment
组合形变热处理|高温与低温联合的形变热处理
-- 来源 -- 英汉 - 翻译参考[网络]
35. thermomechanical analysis
温度 形变分析
-- 来源 -- 英汉 - 翻译参考[网络]
36. thermomechanical process
形变热处理法
-- 来源 -- 英汉 - 翻译参考[网络]
37. thermomechanical curve
热-力学曲线|热变形曲线
-- 来源 -- 英汉 - 翻译参考[网络]
38. thermomechanical analysis (TMA)
热机械分析
-- 来源 -- 英汉 - 翻译参考[网络]
39. thermomechanical treatment
形变热处理
-- 来源 -- 英汉 - 翻译参考[网络]
40. double thermomechanical treatment
二级形变热处理
-- 来源 -- 英汉 - 翻译参考[网络]